Hogue Rubber OverMolded Rifle Stock Remington 700 BDL Short Action Factory Barrel Channel Pillar Bed Synthetic Black
Hogue OverMolded stocks have fiberglass skeletons with the same permanently-bonded rubber coating used on Hogue's popular handgun grips. The non-slip coating is quiet and durable. The grip and forend have a cobblestone texture for a sure grip. All stocks come with swivel studs, straight comb and recoil pads. The pillar bedding in this stock utilizes aluminum bosses embedded in the stock at critical mounting locations. These aluminum pillar beds ensure a rock solid fit to the action of the rifle to give you the best accuracy possible. The rifle stock is also designed to free-float the barrel for maximum accuracy.
- Firearm Fit: Remington 700 BDL Short Action
- Barrel Fit: Standard factory barrel
- Length of Pull: 13-3/4"
- Weight: 2 lbs 10 oz.
Special instructions from Hogue: To maximize the accuracy potential of your Remington 700, your new stock has been designed to free float the barrel and register tightly against the sides of the recoil lug. Although because of slight angular variations in the recoil lug's location in each rifle, it can cause the barrel to contact one side of the barrel channel. This can be left alone and the rifle will operate properly with no modification and some rifles will not need adjustment if the barrel naturally centers itself. If the barrel does not self-center and you desire the optimum accuracy from your rifle, it is necessary to slightly rotate the recoil lug to correctly float the barrel. We have successfully performed this by following these steps:
1. Unload the rifle and remove the bolt.
2. With a pencil, mark the starting orientation between the barrel, lug and action.
3. Lay the action on a solid padded surface while holding the barrel firmly in the weak hand.
4. With a soft medium sized brass hammer, strike the bottom corner of the recoil lug in the opposite direction you want the barrel to float in the stock. The recoil lug is a separate piece of steel held tightly between the barrel and action. It will rotate. Only a very small amount of movement is necessary and can be observed by the pencil mark.
5. Keep making small adjustments while checking the fit until the barrel centers when the floor plate is bolted tightly to the rifle.
Note: If you do not feel confident, we recommend a competent gunsmith perform this adjustment for you. Take these instructions with you.
Another acceptable method is to carve out the recoil lug pocket in the stock and bed it with suitable bedding compound. Again, the rifle will operate properly without any modification to either the stock or the rifle.
As soon as you place your order, you will receive an order confirmation e-mail. This means that we have received your order in our system and pre-authorized your credit card for the purchase. As soon as we receive your order, we check to confirm that it is in stock and available for immediate shipment. If your item is on backorder or unavailable, we will reach out to you via e-mail. If your item(s) are available for immediate shipment (within 5 business days), we will process the charges and submit the order for shipment.
If your order is stock and we process the charges to your credit card, it will ship no later than five business days from the date of your order. We will send you tracking information within 24 hours of your order leaving the warehouse to the e-mail address your provide when checking out. If you do not receive tracking information from us within six business days of your order, feel free to follow up with us at orders@OpticsPros.com
Please inspect the packaging of your item(s) when they arrive, if you notice any damage you should make note of it immediately upon delivery. If your item(s) do arrived damaged, please send photos to Orders@OpticsPros.com and we will process an insurance claim on your behalf.
Cancellations & Refunds:
To ensure prompt, accurate service, all returns require prior authorization by Optics Pros Customer Service Department. Optics Pros will accept returns within 30 days of the original invoice date as long as the products are new and in original, unopened packaging (some restrictions apply). All concerns must be brought to the attention of Customer Service within 48 hours of receipt of merchandise.
We are unable to take back products with opened packaging and used products. Optics Pros is not a warranty repair station, and we cannot accept defective merchandise returns. Defective merchandise is subject to the manufacturer’s specified warranty policy, and the manufacturer should be contacted directly for details. Additionally, we cannot accept returns on clearance items, special order merchandise or products that have been shipped to a third-party.
Our return specialists will issue credit for the return following an inspection, and you will be notified via email if there are any issues or if we are unable to apply credit for the return.
Please Note: All orders cancelled after 24 hours are subject to a $20 administration fee, if your order has not shipped. If you order has shipped, you (the buyer) will also be responsible for actual return shipping charges. Refunds will only be issued to the original credit card that you use when placing your order.
Please Note: A 20% restock fee, and the original actual shipping cost will be deducted from the refund amount for reasons other than manufacturer defect, or a mistake on our part.
We Also Recommend
ZEV Technologies ZEV Pro Barrel GLOCK 17 416R Chromium Stainless Steel 9mm Luger Match Grade Threaded Barrel Gray DLC Finish BBL-17-PROS-GRY
ZEV Technologies Skeletonized Ultra Light Firing Pin Glock All Generations 45 ACP, 10mm Auto Stainless Steel
ZEV Technologies Skeletonized Ultra Light Firing Pin Glock 9mm Luger, 357 Sig, 40 S&W, 45 GAP All Generations Stainless Steel